СИСТЕМА ECD, Diagnostic DTC:P0117, P0118

DTC Code DTC Name
P0117 Engine Coolant Temperature Circuit Low Input
P0118 Engine Coolant Temperature Circuit High Input

DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor.

The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.

Tip:

  • When the engine coolant temperature sensor output is outside the normal range, the ECM determines that there is a malfunction.

  • If DTC P0117 or P0118 is detected, the ECM performs engine control using an estimated engine coolant temperature calculated from the intake air temperature and the intake air volume at the time of engine start.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0117 Engine Coolant Temperature Circuit Low Input

Engine coolant temperature sensor output is higher than 120°C (248°F).

(2 trip detection logic)

  • Short in engine coolant temperature sensor circuit

  • Engine coolant temperature sensor

  • ECM

 Comes on DTC stored
P0118 Engine Coolant Temperature Circuit High Input

Engine coolant temperature sensor output is lower than -30°C (-22°F).

(2 trip detection logic)

  • Open in engine coolant temperature sensor circuit

  • Engine coolant temperature sensor

  • ECM

 Comes on DTC stored
Table 1. DTC Detection Drive Pattern
DTC No. DTC Detection Drive Pattern
P0117 Ignition switch ON for approximately 15 seconds
P0118
Table 2. Related Data List
DTC No. Data List
P0117 Coolant Temp
P0118
Tip:

  • If DTC P0117 or P0118 is stored, the following symptoms may appear:

    • Misfire

    • Combustion noise increases

    • Black smoke

    • White smoke

    • Lack of power

  • When DTC P0117 or P0118 is stored, check the engine coolant temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Coolant Temp.

Table 3. Reference
Temperature Displayed Malfunction
-30°C (-22°F) or less Open circuit
120°C (248°F) or higher Short circuit

WIRING DIAGRAM

A012N0IE02
Table 4.
*a Engine Coolant Temperature Sensor

CAUTION / NOTICE / HINT

Note:

When replacing the ECM, perform ECM Initialization and Registration.

Click here Нажмите здесь

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. READ VALUE USING GTS (COOLANT TEMP)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

      Powertrain > Engine and ECT > Data List
      Tester Display
      Coolant Temp

    4. Read the value.

      Standard
      75 to 100°C (167 to 212°F) with warm engine.
      Result
      Result Proceed to
      -30°C (-22°F) or less A
      120°C (248°F) or higher B
      Between 75 to 100°C (167 to 212°F) C
      Tip:

      • If there is an open circuit, the GTS indicates -30°C (-22°F) or less.

      • If there is a short circuit, the GTS indicates 120°C (248°F) or higher.

    B Нажмите здесь

    C Нажмите здесь

    GO TO STEP 4

    A

  2. READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

    1. Disconnect the engine coolant temperature sensor connector.

    2. Connect terminals B166-1 and B166-2 of the engine coolant temperature sensor connector on the wire harness side.

      A012LJNC02
      *1 Engine Coolant Temperature Sensor
      *2 ECM
      *a

      Front view of wire harness connector

      (to Engine Coolant Temperature Sensor)

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON and turn the GTS on.

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

      Powertrain > Engine and ECT > Data List
      Tester Display
      Coolant Temp

    6. Read the value.

      Standard
      120°C (248°F) or higher.
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK

  3. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

    1. Replace the engine coolant temperature sensor.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  4. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON and wait for 15 seconds or more.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    7. Confirm that the pending DTC is not output again.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT
    NEXT

    END

  5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

    1. Disconnect the engine coolant temperature sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B166-2 - B138-40 (THW) Always Below 1 Ω
      B166-1 - B138-39 (ETHW) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK

  6. CONFIRM ECM (GOOD CONNECTION TO ECM. IF OK, REPLACE ECM)

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 4

  7. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT
    NEXT Нажмите здесь

    GO TO STEP 4

  8. READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

    1. Disconnect the engine coolant temperature sensor connector.

    2. Connect the GTS to the DLC3.

      A012HH1C13
      *1 Engine Coolant Temperature Sensor
      *2 ECM

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

      Powertrain > Engine and ECT > Data List
      Tester Display
      Coolant Temp

    5. Read the value.

      Standard
      -30°C (-22°F) or less.
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK

  9. REPLACE ENGINE COOLANT TEMPERATURE SENSOR

    1. Replace the engine coolant temperature sensor.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 4

  10. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

    1. Disconnect the engine coolant temperature sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B166-2 or B138-40 (THW) - Body ground) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    GO TO STEP 7

    OK

  11. REPLACE ECM

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 4