СИСТЕМА МЕХАНИЧЕСКОЙ ТРАНСМИССИИ "MULTIMODE", Diagnostic DTC:P0909

DTC Code DTC Name
P0909 Gate Select Control Error

DESCRIPTION

In the multi-mode manual transaxle system, the transaxle gear is shifted up and down by the TCM using a shift and select actuator. The shift and select actuator assembly consists of two motors (shift motor and select motor), stroke sensors (shift stroke sensor and select stroke sensor) and gears which move the shift and select lever shaft. The select motor moves the shift and select lever shaft in the select direction in accordance with the signal from the TCM.

This DTC is stored in accordance with the stroke speed of the shift and select actuator or the difference between the target select position and the actual select position. Therefore, if malfunctions occur in the select stroke sensor or the select motor circuit, the DTCs relating to the sensor or motor circuit open/short (DTC P0905, P0906, P0907 and/or P0910) are stored before this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P0909 Gate Select Control Error

The TCM detects the following conditions simultaneously for 2.0 seconds:

(1-trip detection logic)

  1. Select motor current is 16 A or more, or -16 A or less.

  2. Difference between target select position and actual select position is 0.3 mm (0.0118 in.) or more.

  3. Shift and select actuator movement is 122 mm/sec (4.8 in./sec) or less.

  • Select stroke sensor

  • Shift and select actuator assembly (select motor)

  • TCM

  • Transaxle assembly

 Does not come on Comes on DTC stored

WIRING DIAGRAM

A012GN1E03
Table 1.
*a Sub
*b Main
*c Select Stroke Sensor
*d Shift and Select Actuator Assembly (Select Motor)

CAUTION / NOTICE / HINT

Note:

When installing parts related to the multi-mode manual transaxle system, perform the initialization and learning and synchronization position calibration procedures. In addition, the required operations differ according to the parts to be installed. Proceed with the operation in the order shown in the table below.

Table 2. After Installation
Part Installed Part Installed See Procedure

  • Transaxle assembly

  • Transaxle parts (inside gear box)

  • TCM

  • Clutch actuator assembly

  • Clutch disc and clutch cover

  • Clutch release with bearing cylinder assembly

  • Flywheel

  • Crankshaft

1. Initialization of multi-mode manual transaxle system

[Tester display: Initialization of ECU]

Нажмите здесь

2. Learning of multi-mode manual transaxle system
3. Synchronization position calibration

  • Shift and select actuator

  • Shift stroke sensor

  • Select stroke sensor

1. Initialization of multi-mode manual transaxle system

[Tester display: Initialization of transmission]
2. Learning of multi-mode manual transaxle system
3. Synchronization position calibration

  • Clutch stroke sensor

1. Initialization of multi-mode manual transaxle system

[Tester display: Initialization of clutch]
2. Learning of multi-mode manual transaxle system

If the sensor or actuator is installed without the initialization and learning procedures, it may cause driving performance degradation or system component breakage.

Tip:

If the symptom still occurs even after checking the shift heads and shift fork shafts for dirt, wear, and defects and replacing the defective parts, replace the TCM.

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS (TARGET GEAR POSITION CONTROL)

    1. Remove the shift and select actuator assembly.

      Click hereНажмите здесь

    2. Connect the shift and select actuator assembly connector.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Multi-Mode M/T / Active Test / Target Gear Position Control.

      Powertrain > Multi-Mode M/T > Active Test
      Tester Display
      Target Gear Position Control
      OK
      Shift and select actuator moves smoothly in accordance with the GTS operation.
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK

  2. INSPECT SELECT STROKE SENSOR

    Click hereНажмите здесь

    Result
    Proceed to
    OK
    NG
    NG Нажмите здесь

    OK

  3. INSPECT TCM (MSL TERMINAL VOLTAGE)

    1. Turn the ignition switch to ON.

    2. Measure the voltage according to the value(s) in the table below.

      A012FN0C10
      *a

      Component with harness connected

      (TCM)
      Standard Voltage
      Tester Connection Condition Specified Condition
      A103-1 (MSL+) - Body ground Ignition switch ON 4.0 to 7.0 V
      A103-2 (MSL-) - Body ground Ignition switch ON 4.0 to 7.0 V

    3. Turn the ignition switch off.

      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK

  4. INSPECT TRANSAXLE ASSEMBLY

    1. Remove the transaxle assembly.

      Click hereНажмите здесь

    2. Check for dirt, wear and defects in the gear shift mechanical system (synchronizer rings, shift forks, hub sleeves, etc.).

      OK
      No defective parts in the transaxle assembly.
      Result
      Proceed to
      OK
      NG
    NG

    REPAIR OR REPLACE DEFECTIVE PART IN TRANSAXLE ASSEMBLY

    OK

  5. REPLACE TCM

    1. Replace the TCM.

      for LHD: Click here Нажмите здесь

      for RHD: Click here Нажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  6. PERFORM INITIALIZATION

    1. Perform the initialization and learning procedure.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

    END

  7. CHECK TERMINAL CONDITION (TCM)

    Click hereНажмите здесь

    Result
    Proceed to
    OK
    NG
    NG

    CONNECT CORRECTLY

    OK

  8. INSPECT SELECT MOTOR CIRCUIT

    1. Disconnect the TCM connector.

    2. Measure the resistance according to the value(s) in the table below.

      A012GYZC02
      *a

      Front view of wire harness connector

      (to TCM)
      Standard Resistance
      Tester Connection Condition Specified Condition
      A103-1 (MSL+) - A103-2 (MSL-) Always Below 10 Ω
      A103-1 (MSL+) - Body ground Always 10 kΩ or higher
      A103-2 (MSL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK

  9. REPLACE TCM

    1. Replace the TCM.

      for LHD: Click here Нажмите здесь

      for RHD: Click here Нажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  10. PERFORM INITIALIZATION

    1. Perform the initialization and learning procedure.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

    END

  11. CHECK TERMINAL CONDITION (SELECT MOTOR)

    1. Disconnect the select motor connector.

    2. Check the connections of the select motor connector.

      OK
      The select motor and wire harness connectors and connector terminals are connected securely and are not bent, rusted, or damaged.
      Result
      Proceed to
      OK
      NG
    NG

    CONNECT CORRECTLY

    OK

  12. CHECK HARNESS AND CONNECTOR (TCM - SELECT MOTOR)

    1. Disconnect the TCM connector.

    2. Disconnect the select motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A103-1 (MSL+) - B140-2 (MSL+) Always Below 1 Ω
      A103-2 (MSL-) - B140-1 (MSL-) Always Below 1 Ω
      A103-1 (MSL+) or B140-2 (MSL+) - Body ground Always 10 kΩ or higher
      A103-2 (MSL-) or B140-1 (MSL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. INSPECT SHIFT AND SELECT ACTUATOR ASSEMBLY (SELECT MOTOR)

    1. Measure the resistance according to the value(s) in the table below.

      A012I42C02
      *a

      Component without harness connected

      (Shift and Select Actuator Assembly (Select Motor))
      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (MSL-) - 2 (MSL+) Always Below 10 Ω
      1 (MSL-) - Body ground Always 10 kΩ or higher
      2 (MSL+) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    OK

    CHECK INTERMITTENT PROBLEMS Click hereНажмите здесь

    NG Нажмите здесь

    GO TO STEP 16

  14. REPLACE SELECT STROKE SENSOR

    1. Replace the select stroke sensor.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  15. PERFORM INITIALIZATION

    1. Perform the initialization and learning procedure.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

    END

  16. REPLACE SHIFT AND SELECT ACTUATOR ASSEMBLY

    1. Replace the shift and select actuator assembly.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  17. PERFORM INITIALIZATION

    1. Perform the initialization and learning procedure.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

    END