PROCEDURE
INSTALL CAMSHAFT
Turn the crankshaft to set the key in the BTDC 75° position.
*1 | Key |
*a | TDC Mark |
Apply engine oil to each camshaft journal and cam.
Examine the front marks and numbers of the camshaft bearing caps, and check that the order is as shown in the illustration. Then, temporarily install the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps with the 10 bolts.
Engine Front |
Do not tilt the valve rocker arm sub-assemblies when installing the camshaft onto the cylinder head sub-assembly.
Using several steps, temporarily tighten the 10 bolts, and then tighten them to the specified torque in the order shown in the illustration.
INSTALL CHAIN SUB-ASSEMBLY
Click hereНажмите здесь
INSTALL NO. 1 CHAIN VIBRATION DAMPER
Click hereНажмите здесь
INSTALL CHAIN TENSIONER SLIPPER
Click hereНажмите здесь
INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Click hereНажмите здесь
INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Click hereНажмите здесь
CONNECT INLET WATER HOSE LH
Connect the inlet water hose LH.
The clip on the inlet water housing side can be installed with any orientation, as long as it does not contact any of the surrounding parts.
INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY
Click here Нажмите здесь
INSTALL NO. 2 TIMING CHAIN COVER
Click hereНажмите здесь
INSTALL ENGINE MOUNTING BRACKET RH
Click hereНажмите здесь
CHECK VALVE CLEARANCE
Click here Нажмите здесь
ADJUST VALVE CLEARANCE
Click here Нажмите здесь
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Click hereНажмите здесь
INSTALL HARNESS BRACKET
Click hereНажмите здесь
INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
Click hereНажмите здесь
INSTALL VACUUM PUMP ASSEMBLY
Click hereНажмите здесь
INSTALL CAMSHAFT POSITION SENSOR (w/o Stop And Start System)
Apply a light coat of engine oil to the O-ring of the camshaft position sensor.
*a | O-ring |
If reusing the camshaft position sensor, be sure to inspect the O-ring.
Install the camshaft position sensor with the bolt.
If the camshaft position sensor has been dropped or subjected to a strong impact, replace it.
Make sure that the O-ring is not cracked or moved out of place during installation.
INSTALL NO. 2 CYLINDER HEAD COVER
Click hereНажмите здесь
INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Install a new O-ring to the water by-pass pipe sub-assembly.
Apply water to the water inlet housing O-ring fitting surface before installing the water by-pass pipe sub-assembly.
Install the water by-pass pipe sub-assembly with the 2 bolts in the order shown in the illustration.
Connect the oil cooler hose.
*a | View A |
*b | Front |
*c | LH |
Connect the water by-pass hose.
*a | Upper |
*b | View A |
INSTALL NO. 4 WATER BY-PASS HOSE
Click hereНажмите здесь
INSTALL NO. 2 OIL COOLER HOSE
Click hereНажмите здесь
INSTALL NO. 1 SUPPLY PUMP DRIVE COUPLING
Click hereНажмите здесь
TEMPORARILY INSTALL SUPPLY PUMP ASSEMBLY
Click hereНажмите здесь
INSTALL FUEL INLET PIPE SUB-ASSEMBLY
Click hereНажмите здесь
CONNECT NO. 2 FUEL HOSE
Connect the No. 2 fuel hose to the supply pump assembly.
INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY
Click hereНажмите здесь
INSTALL NOZZLE LEAKAGE PIPE SET CLAMP
Click hereНажмите здесь
INSTALL INTAKE AIR CONNECTOR WITH DIESEL THROTTLE BODY
Click hereНажмите здесь
INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Click hereНажмите здесь
INSTALL ENGINE OIL LEVEL DIPSTICK
Click hereНажмите здесь
INSTALL EGR VALVE (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
Click hereНажмите здесь
INSTALL HARNESS BRACKET
Click here Нажмите здесь
INSTALL NO. 1 EGR COOLER BRACKET
Click hereНажмите здесь
INSTALL EGR WITH COOLER PIPE ASSEMBLY
Click hereНажмите здесь
INSTALL GENERATOR BRACKET
Click hereНажмите здесь
INSTALL GENERATOR ASSEMBLY
Click hereНажмите здесь
INSTALL ENGINE COVER BRACKET (w/ No. 1 Engine Cover)
Click hereНажмите здесь
REMOVE ENGINE STAND
Click here Нажмите здесь