ПЕРЕДНИЙ ПРИВОДНОЙ ВАЛ В СБОРЕ (для моделей с 1AD-FTV) УСТАНОВКА

PROCEDURE

  1. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

    1. Install a new front drive shaft hole snap ring LH.

      Note:

      Face the end gap of the front drive shaft hole snap ring downward.

  2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

    1. Coat the splines of the front drive inboard joint assembly with gear oil.

    2. Coat the lip of the transmission case oil seal with MP grease.

    3. Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

      A012IVJ
      Note:

      • Face the end gap of the front drive shaft hole snap ring LH downward.

      • Do not damage the transmission case oil seal.

      • Do not damage the front axle inboard joint boot.

      • Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring LH.

      Tip:

      Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.

    4. Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.

      A012I0LC01
      *a Matchmark
      Note:

      Be careful not to damage the front axle outboard joint boot.

  3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

    1. Coat the splines of the front drive inboard joint assembly with gear oil.

    2. Coat the lip of the transaxle case oil seal with MP grease.

    3. Align the inboard joint splines, and securely insert the front drive shaft assembly RH.

      Note:

      Do not damage the transaxle case oil seal, inboard joint boot or front drive shaft dust cover.

    4. Install the front drive shaft assembly RH with the 2 bolts.

      A012FZ3
      Момент затяжки
      63.7 N*m  { 650 kgf*cm, 47 ft.*lbf }

  4. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

    Click here Нажмите здесь

  5. INSTALL FRONT STABILIZER LINK ASSEMBLY

    Click here Нажмите здесь

  6. CONNECT TIE ROD END SUB-ASSEMBLY

    Click here Нажмите здесь

  7. INSTALL FRONT FLEXIBLE HOSE

    Click here Нажмите здесь

  8. INSTALL FRONT SPEED SENSOR

    Click here Нажмите здесь

  9. INSTALL FRONT AXLE SHAFT NUT

    1. Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

      Note:

      • Be sure to perform this work even when using a new drive shaft.

      • Keep the threaded parts free of oil and foreign matter.

    2. Using a 30 mm socket wrench, install the front axle shaft nut.

      A012MGJ
      Момент затяжки
      292 N*m  { 2978 kgf*cm, 215 ft.*lbf }
      Tip:

      Keep depressing the brake pedal to prevent the drive shaft from rotating.

    3. Using a chisel and a hammer, stake the front axle shaft nut.

  10. ADD MANUAL TRANSAXLE OIL

    Click hereНажмите здесь

  11. INSPECT FOR OIL LEAK

  12. INSTALL REAR ENGINE UNDER COVER LH

  13. INSTALL REAR ENGINE UNDER COVER RH

  14. INSTALL NO. 1 ENGINE UNDER COVER

  15. INSTALL FRONT WHEELS

    Момент затяжки
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  16. ADJUST FRONT WHEEL ALIGNMENT

    Click here Нажмите здесь

  17. CHECK FOR SPEED SENSOR SIGNAL

    Click hereНажмите здесь