СИСТЕМА ECD, Diagnostic DTC:P244A, P244C, P2463

DTC Code DTC Name
P244A Diesel Particulate Filter Differential Pressure Too Low
P244C Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 1
P2463 Diesel Particulate Filter Restriction - Soot Accumulation

DESCRIPTION

DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures, however PM accumulation increases at low catalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.

A012JIUC01
*1 Oxidation Catalyst *2 DPF Catalyst
*a Reference *b Exhaust Gas
*c Enlarged Illustration - -
DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P244A Diesel Particulate Filter Differential Pressure Too Low When PM forced regeneration is manually performed, PM forced regeneration does not finish even after 60 minutes or more elapse (1 trip detection logic).

  • Oxidation catalytic converter (built into exhaust manifold converter sub-assembly)

  • DPF catalytic converter (Exhaust manifold converter sub-assembly)

  • Exhaust fuel addition injector assembly

Common Inspection Item:

  • Fuel injection system

  • Intake/Exhaust system

 Comes on DTC stored
P244C Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 1 During PM forced regeneration, catalyst temperature does not increase sufficiently for 3 minutes (1 trip detection logic).

  • Oxidation catalytic converter (built into exhaust manifold converter sub-assembly)

  • DPF catalytic converter (Exhaust manifold converter sub-assembly)

  • Exhaust fuel addition injector assembly

Common Inspection Item:

  • Fuel injection system

  • Intake/Exhaust system

 Comes on DTC stored
P2463 Diesel Particulate Filter Restriction - Soot Accumulation While driving, PM accumulation amount exceeds the limit (1 trip detection logic).

  • Oxidation catalytic converter (built into exhaust manifold converter sub-assembly)

  • DPF catalytic converter (Exhaust manifold converter sub-assembly)

  • Exhaust fuel addition injector assembly

Common Inspection Item:

  • Fuel injection system

  • Intake/Exhaust system

 Comes on DTC stored
Tip:

PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).

Table 1. Related Data List
DTC No. Data List
P244A

  • Exhaust Fuel Addition FB

  • Catalyst Differential Press

  • Exhaust Temperature B1S3
P244C
P2463

MONITOR DESCRIPTION

The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst and also monitors exhaust gas temperature to detect a malfunction in the DPF catalyst.

  • Excessive PM accumulation:

    The ECM monitors the PM accumulation ratio and when the accumulated PM volume in the DPF catalyst exceeds the limit, the ECM illuminates the MIL.

  • Abnormal catalyst temperature increase:

    The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assembly adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DPF catalyst is abnormal and illuminates the MIL.

  • Catalytic converter differential pressure too low:

    When PM forced regeneration is manually performed, PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst and illuminates the MIL.

A012FJ3E07

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P244A PM forced regeneration
P244C
P2463

CAUTION / NOTICE / HINT

Note:

  • After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here Нажмите здесь

  • After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click hereНажмите здесь).

  • After replacing the suction control valve, the ECM needs initialization.

    Click hereНажмите здесь

  • After replacing an injector assembly, the ECM needs registration.

    Click hereНажмите здесь

  • After replacing the exhaust manifold converter sub-assembly (DPF catalytic converter), clear the thermal deterioration data stored in the ECM.

    Click hereНажмите здесь

Tip:

  • If DTC P244A, P244B, P244C or P2463 is stored, fail-safe controls engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI-MAIN fuse or battery terminal and waiting for 60 seconds or more before connecting it again.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Record the stored DTC and freeze frame data.

      Powertrain > Engine and ECT > Trouble Codes

    6. Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

      Tip:

      • When the Exhaust Fuel Addition FB value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.

      • When the Catalyst Differential Press value is more than 0.47, it indicates a high possibility that DPF catalyst is clogged.

      Result
      Proceed to
      NEXT
    NEXT

  2. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244A, P244C AND P2463)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      ResultProceed to
      DTC P244A, P244C or P2463 is outputA
      DTC P244B is output at the same time as P2463*B
      Other relevant DTCs are outputC
      Tip:

      • *: When P244B is output at the same time as P2463, perform troubleshooting for P244B.

      • When DTC P1603, P1604 or P1608 is output in addition to P244C, perform troubleshooting for P1603, P1604 or P1608 first.

    B

    GO TO DTC P244B Click hereНажмите здесь

    A Нажмите здесь

    GO TO STEP 4

    C

  3. GO TO DTC CHART

    1. Diagnose relevant DTCs.

      Click here Нажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  4. CHECK FOR BLACK SMOKE

    1. Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.

    2. Stop the vehicle and allow the engine to idle.

    3. Fully depress the accelerator pedal for 5 seconds, and then release it. [A]

    4. Repeat the procedure [A] 10 times. [B]

    5. Check for black smoke emission during the procedures [A] and [B].

      OK
      Black smoke is emitted less than 5 times.
      Tip:

      Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.

      Result
      Proceed to
      OK
      NG
    OK Нажмите здесь

    NG

  5. REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

    1. Even though it has been determined that the exhaust manifold converter sub-assembly (DPF catalytic converter) needs to be replaced, make sure to perform all diagnostic procedures for DTC P244A, P244C and P2463 before replacing it.

      Tip:

      This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.

      Result
      Proceed to
      NEXT
    NEXT

  6. CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)

    1. Clear the DTC and Exhaust Fuel Addition FB value by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN fuse for 60 seconds or more.

      Tip:

      • The accumulated PM volume stored in the ECM cannot be initialized using the GTS.

      • To perform PM forced regeneration, it is necessary to perform initialization of the accumulated PM volume stored in the ECM.

    2. Connect the GTS to the DLC3.

    3. Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.

    4. Move the shift lever to neutral and set the parking brake.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPF Rejuvenate (PM) / Data List / Diesel Exhaust / Exhaust Temperature B1S3.

      Powertrain > Engine and ECT > Active Test
      Active Test Display
      Activate the DPF Rejuvenate (PM)
      Data List Display
      Exhaust Temperature B1S3

    7. Perform the Active Test while the vehicle is driven at a constant vehicle speed within 50 to 100 km/h (31 to 62 mph) (transaxle in 3rd gear) for more than 15 minutes.

      ОСТОРОЖНО

      • Be aware of excessive heat on and around the exhaust pipes during PM forced regeneration.

      • When performing the confirmation driving pattern, obey all speed limits and traffic laws.

      Note:

      If PM forced regeneration stops, repair the malfunction that caused it to stop, and perform it again to complete the operation.

      Tip:

      • While the "Activate the DPF Rejuvenate (PM)" Active Test is being performed, the accelerator opening angle should be kept as constant as possible.

      • PM forced regeneration completes in 15 to 40 minutes.

      • PM forced regeneration time changes depending on PM Accumulation Ratio and driving conditions.

      • A fail-safe stops PM forced regeneration if Catalyst Differential Press increases too much during regeneration.

      • Exhaust Temperature B1S3 becomes 500°C (932°F) or higher within 20 minutes of PM forced regeneration start.

      • PM forced regeneration will be stopped if the accelerator pedal is depressed during regeneration. In this case, PM forced regeneration needs to be performed again.

      • Even if PM forced regeneration stops while it is occurring, the GTS displays Compl (complete) for DPNR/DPF Status Reju(PM).

    8. Check if the temperature increases or abnormal white smoke occurs during PM forced regeneration.

      Result
      Result Proceed to
      No abnormal white smoke occurs but the temperature of Exhaust Temperature B1S3 does not reach 450°C (842°F) or higher during PM forced regeneration A
      Abnormal white smoke occurs and the temperature of Exhaust Temperature B1S3 reaches 300°C (572°F) or higher during PM forced regeneration B
      Except above* C
      Tip:

      • When excessive white smoke occurs only during PM forced regeneration, uncombusted fuel passes through due to the deterioration of DPF catalyst is suspected.

      • When combustion control has a malfunction, deterioration or abnormality of driving performance can be felt despite PM forced regeneration.

      • If Exhaust Temperature B1S3 does not reach 450°C (842°F) or higher, the exhaust fuel addition injector assembly may be clogged.

      • *: Excessive accumulation of PM is caused by a worsening in combustion conditions and an increase in black smoke due to a malfunction in the control system.

    B Нажмите здесь

    C Нажмите здесь

    A

  7. REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

    1. Even though it has been determined that the exhaust fuel addition injector assembly needs to be replaced, make sure to perform all diagnostic procedures for DTC P244A, P244C and P2463 before replacing it.

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 9

  8. REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

    1. Even though it has been determined that the exhaust manifold converter sub-assembly (DPF catalytic converter) needs to be replaced, make sure to perform all diagnostic procedures for DTC P244A, P244C and P2463 before replacing it.

      Tip:

      This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.

      Result
      Proceed to
      NEXT
    NEXT

  9. CHECK FUEL INJECTION SYSTEM

    1. Check the fuel injection system.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  10. CHECK INTAKE / EXHAUST SYSTEM

    1. Check the intake/exhaust system.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  11. REPAIR OR REPLACE MALFUNCTIONING PARTS

    Tip:

    Replace the following items only when it has been determined necessary based on diagnosis for DTC P244A, P244C and P2463.

    1. Replace the exhaust manifold converter sub-assembly (DPF catalytic converter).

      Click hereНажмите здесь

      Note:

      Perform Initialization procedure for DPF catalyst record clear.

      Click hereНажмите здесь

    2. Replace the exhaust fuel addition injector assembly.

      Click hereНажмите здесь

    3. Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system and intake/exhaust system.

      Result
      Proceed to
      NEXT
    NEXT

  12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Clear the DTC and Exhaust Fuel Addition FB value by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN fuse for 60 seconds or more.

      Tip:

      • The accumulated PM volume stored in the ECM cannot be initialized using the GTS.

      • To perform PM forced regeneration, it is necessary to perform initialization of the accumulated PM volume stored in the ECM.

    2. Connect the GTS to the DLC3.

    3. Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.

    4. Move the shift lever to neutral and set the parking brake.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPF Rejuvenate (PM) / Data List / Diesel Exhaust / PM Accumulation Ratio.

      Powertrain > Engine and ECT > Active Test
      Active Test Display
      Activate the DPF Rejuvenate (PM)
      Data List Display
      PM Accumulation Ratio

    7. Perform the Active Test while the vehicle is driven at a constant vehicle speed within 50 to 100 km/h (31 to 62 mph) (transmission in 3rd gear) for more than 15 minutes.

      ОСТОРОЖНО

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

      Tip:

      • While the "Activate the DPF Rejuvenate (PM)" Active Test is being performed, the accelerator opening angle should be kept as constant as possible.

      • When you start driving, "DPNR/DPF Status Reju(PM)" on the Data List displays "Compl". However, continue to drive the vehicle until "PM Accumulation Ratio" drops to 0%.

      • Once "PM Accumulation Ratio" drops to 0%, regeneration is complete.

    8. Continue to drive the vehicle until "PM Accumulation Ratio" drops to 0%.

      ОСТОРОЖНО

      Be aware of excessive heat on and around the exhaust pipes during PM forced regeneration.

      Note:

      If PM forced regeneration stops, repair the malfunction that caused it to stop, and perform it again to complete the operation.

      Tip:

      • PM forced regeneration completes in 15 to 40 minutes.

      • PM forced regeneration time changes depending on PM Accumulation Ratio and driving conditions.

      • A fail-safe stops PM forced regeneration if Catalyst Differential Press increases too much during regeneration.

      • Exhaust Temperature B1S3 becomes 500°C (932°F) or higher within 20 minutes of PM forced regeneration start.

      • PM forced regeneration will be stopped if the accelerator pedal is depressed during regeneration. In this case, PM forced regeneration needs to be performed again.

      • Even if PM forced regeneration stops while it is occurring, the GTS displays Compl (complete) for DPNR/DPF Status Reju(PM).

      Result
      Proceed to
      NEXT
    NEXT

    END