СИСТЕМА ECD РЕГИСТРАЦИЯ

PROCEDURE

  1. LEARNING VALUES CONFIRMATION

    This procedure uses the GTS to display the learned values (injector compensation code, pilot quantity initial learning value, pilot quantity deterioration learning value, pilot quantity current learning value, crank time compensation learning value, catalyst deterioration learning value and A/F sensor compensation learning value) stored in the ECM.

    A012FWTE01
    Tip:

    • A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

      A012GDM

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note:

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Confirmation.

      Powertrain > Engine and ECT > Utility
      Tester Display
      Learning Values Confirmation

    4. Press "Next".

      A012JDY

    5. Press "Next" again to proceed.

      A012L09

    6. Select the value to confirm and press "Next".

      A012G58

    7. When the next screen is displayed, confirm the contents and press "Exit".

      A012J4WC01
      *a Example - -

  2. LEARNING VALUES SAVE

    This procedure uses the GTS to save the learned values (injector compensation code, pilot quantity initial learning value, pilot quantity deterioration learning value, pilot quantity current learning value, crank time compensation learning value, catalyst deterioration learning value and A/F sensor compensation learning value) stored in the ECM in the GTS depending on the components being replaced.

    A012IOLE12
    Tip:

    • When replacing the engine assembly, injector assembly, exhaust manifold converter sub-assembly or the air fuel ratio sensor together with the ECM, this function automatically determines the data which can be transferred (old data) and saves the data in the GTS.

    • When there is no data to read from the ECM, manually perform the procedure to register each compensation code and learning value in the ECM.

      A012JOQ

    • A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

      A012KZ7

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note:

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.

      Powertrain > Engine and ECT > Utility
      Tester Display
      Learning Values Save

    4. Press "Next".

      A012L3P

    5. Press "Next" again to proceed.

      A012MSB

    6. Select any components being replaced and press "Next". If no applicable components are displayed, press "Next" without selecting anything.

      A012LE9

    7. If the overwrite confirmation screen is displayed, press "Overwrite".

      A012F2W

    8. When the operation is finished, confirm the date and time of the save operation, and press "Exit".

      A012JTD

  3. LEARNING VALUES WRITE

    This procedure uses the GTS to write all of the learned values (injector compensation code, pilot quantity initial learning value, pilot quantity deterioration learning value, pilot quantity current learning value, crank time compensation learning value, catalyst deterioration learning value and A/F sensor compensation learning value) stored in the GTS to the ECM.

    A012ITKE04
    Tip:

    • A malfunction may occur when writing the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

      A012JT3

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note:

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.

      Powertrain > Engine and ECT > Utility
      Tester Display
      Learning Values Write

    4. Press "Next".

      A012M17

    5. Press "Next" again to proceed.

      A012LLJ

    6. If the "Error Learning Values Write" screen indicating a problem with the saved value(s) or that there are no saved values is displayed, perform "Learning Values Save" again.

      A012GCY

    7. Confirm the date and time of the save operation, and then press "Yes".

      A012L2B

    8. Confirm the contents, and then press "Next".

      A012HMT

    9. If any instructions are displayed on the GTS, manually perform the procedure to register each applicable compensation code or learning value in the ECM.

      A012MC2

    10. Clear the DTCs.

  4. INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

    Note:

    • When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

    • Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

    • When an injector compensation code is input into the ECM, the pilot quantity learning values stored in the ECM are initialized. Also, DTC P062F is stored when the pilot quantity learning values are initialized.

    A012GHTC02
    *a Example
    *b Injector Compensation Code

    1. After replacing injector assembly with new one, input compensation code of the injector assembly into the ECM as follows:

      Tip:

      • Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.

      • When only one or more injector assemblies are replaced, input the injector compensation code(s), perform pilot quantity learning, and then clear the DTCs.

      • When the ignition switch is turned to ON after replacing the ECM, DTC P062F is stored. This indicates that the injector compensation code(s) need to be registered. Manually clear the DTC upon completion of pilot quantity learning.

      1. Input the compensation code(s), which is/are imprinted on the head portion(s) of the new injector(s), into the GTS.

      2. Input the new compensation code(s) into the ECM using the GTS.

      3. Turn the GTS off and turn the ignition switch off.

      4. Wait for at least 30 seconds.

      5. Turn the ignition switch to ON and turn the GTS on.

      6. Perform pilot quantity learning.

      7. Clear the DTC P062F stored in the ECM using the GTS.

        Powertrain > Engine and ECT > Clear DTCs
        Note:

        If the DTCs are cleared without performing pilot quantity learning, DTC P062F is stored the next time the ignition switch is turned to ON.

    2. Register compensation codes.

      A012L6LE06

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

        Note:

        Do not start the engine.

      3. Turn the GTS on.

      4. Enter the following menus: Powertrain / Engine and ECT / Utility / Injector Compensation.

        A012MKS
        Powertrain > Engine and ECT > Utility
        Tester Display
        Injector Compensation

      5. Press "Next".

      6. Press "Next" again to proceed.

        A012KPW

      7. Select "Set Compensation Code".

        A012N2J

      8. Press "Next".

      9. Select the number of the cylinder corresponding to the injector compensation code that you want to register.

        A012IR9

      10. Press "Next".

      11. Register compensation code.

        A012FJ1

        1. Press "Input".

        2. Manually input the cylinder compensation code using the keyboard on the GTS screen. The code is a 30-digit, alphanumeric value printed on the injector assembly head portion.

          A012IZB
          Tip:

          Each injector compensation code is unique. The compensation code for each selected cylinder must be input into the GTS correctly.

        3. Confirm that the compensation code for the selected cylinder is correct, and then press "OK".

      12. Check that the compensation code displayed on the screen is correct by comparing it with the 30-digit alphanumeric value on the head portion of the injector assembly.

        A012H7RC01
        *a Example
        Note:

        If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

        Tip:

        • If a wrong compensation code is input or read, return to the Input Value screen by pressing "Input".

        • The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

      13. Press "Next" to register the compensation code in the ECM.

        Tip:

        • If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

        • If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

      14. If you want to continue with other compensation code registrations, press "Next". To finish the registration, press "Exit".

        A012JRO

      15. Turn the ignition switch off, and then turn the GTS off.

      16. Wait for at least 30 seconds.

      17. Turn the ignition switch to ON, and then turn the GTS on.

      18. Perform pilot quantity learning.

      19. Clear the DTC P062F stored in the ECM using the GTS.

        Powertrain > Engine and ECT > Clear DTCs
        Note:

        If the DTCs are cleared without performing pilot quantity learning, DTC P062F is stored the next time the ignition switch is turned to ON.

  5. PILOT QUANTITY LEARNING

    • "Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning(Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.

    • This procedure uses the GTS to perform "Pilot Quantity Learning".

    • When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).

    A012IT9E09
    Note:

    After completing this procedure, clear the DTCs using the GTS.

    Tip:

    • If "Exit" is pressed during the step where the accelerator pedal is operated and "Pilot Quantity Learning" is canceled, turn the ignition switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.

      A012HAN

    • If an error occurs during learning, check the vehicle condition after turning the ignition switch off, and then perform learning again.

    • If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the ignition switch off, and then perform learning again.

    • A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

      A012MP7

    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot Quantity Learning.

      Powertrain > Engine and ECT > Utility
      Tester Display
      Pilot Quantity Learning

    5. Press "Next".

      A012FS4

    6. Press "Next" again to proceed.

      A012K0D

    7. Confirm that the atmospheric pressure screen is displayed.

      A012GA8C01
      *a Example

      1. Confirm the displayed atmospheric pressure.

        Standard
        Atmosphere Pressure is 85 kPa or higher
        Note:

        • If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".

        • If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.

      2. If the atmospheric pressure is within the standard range, proceed to the next screen.

    8. Confirm the condition of the engine and wait until learning can be performed.

      A012F8VC01
      *a Example
      Table 1. Essential Conditions for Learning
      GTS Display Standard
      Coolant Temp 70 to 100°C
      Intake Air -25 to 120°C
      Fuel Temperature 30 to 96°C
      Fuel Return Temp 35 to 110°C
      Battery Voltage 10 V or higher
      Pilot Quantity State(CAT) READY
      Tip:

      • If the values deviate from the standard above, "Pilot Quantity Learning" enters a standby state or is canceled.

      • When the display indicates that "Pilot Quantity State(CAT)" is NG, perform "Pilot Quantity Learning" after performing the "Activate the DPF Rejuvenate (PM)" Active Test using the GTS.

        Click hereНажмите здесь

      • When the essential conditions to perform learning are met, the screen will change automatically.

      Note:

      • If "Activate the DPF Rejuvenate (PM)" is performed after an injector compensation code is input but before "Pilot Quantity Learning" is performed, DTC P062F is stored and the MIL illuminates due to "Pilot Quantity Learning" being incomplete.

      • Using the GTS, make sure that DTCs other than DTC P062F are not output.

      • If DTCs other than DTC P062F are output, perform troubleshooting for those DTCs, and then perform "Activate the DPF Rejuvenate (PM)".

      Tip:

      DTC P062F is stored when the value registered in the ECM for an input injector compensation code, catalyst deterioration learning value and/or pilot quantity deterioration learning value is the initial value.

    9. Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or higher for no more than 2 seconds, and then let the engine return to idling.

      A012LUZC01
      *a Example
      A012FXA
      Tip:

      • After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.

      • It is possible to confirm the status of the learning operation during "Pilot Quantity Learning" by observing the blinking pattern of the glow indicator light.

      Table 2. Glow Indicator Light Blinking Pattern
      Learning Status Glow Indicator Light Condition
      Conditions essential to start learning have not been met Blinking at 0.5 second intervals
      Conditions essential to start learning have been met Blinking at 1 second intervals
      During racing (learning is being performed) Blinking at 1 second intervals
      Learning is finished Off
      Learning has been canceled Blinking at 1.5 second intervals
      Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern) Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)
      A012I7QE05
      A012HZKE06

    10. When the screen changes, press "Exit".

      A012LNQ

    11. Turn the ignition switch off, and then turn the GTS off.

    12. Wait for at least 10 seconds.

    13. Turn the ignition switch to ON, and then turn the GTS on.

    14. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    15. Turn the ignition switch off.

      Note:

      Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the ignition switch off.

      Tip:

      • The EFI-MAIN relay turns off after the learned value is stored in the ECM.

      • The EFI-MAIN relay turns off within approximately 5 to 10 seconds of turning the ignition switch off.

  6. PILOT QUANTITY LEARNING(DETAIL)

    • "Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning(Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.

      It takes time to clear the learned values and perform learning for all cylinders.

    • This procedure uses the GTS to perform "Pilot Quantity Learning(Detail)".

    • When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).

    A012IT9E08
    Note:

    After completing this procedure, clear the DTCs using the GTS.

    Tip:

    • If "Exit" is pressed during the step where the accelerator pedal is operated and "Pilot Quantity Learning(Detail)" is canceled, turn the ignition switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.

      A012KDG

    • If an error occurs during learning, check the vehicle condition after turning the ignition switch off, and then perform learning again.

    • If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the ignition switch off, and then perform learning again.

    • A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

      A012G7ZC01
      *a Example

    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot Quantity Learning(Detail).

      Powertrain > Engine and ECT > Utility
      Tester Display
      Pilot Quantity Learning(Detail)

    5. Press "Next".

      A012FVW

    6. Press "Next" again to proceed.

      A012FOB

    7. Confirm that the atmospheric pressure screen is displayed.

      A012FBIC01
      *a Example

      1. Confirm the displayed atmospheric pressure.

        Standard
        Atmosphere Pressure is 85 kPa or higher
        Note:

        • If the atmospheric pressure is below the standard range, "Pilot Quantity Learning(Detail)" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".

        • If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning(Detail)" is performed, learning will not be completed.

      2. If the atmospheric pressure is within the standard range, proceed to the next screen.

    8. Confirm the condition of the engine and wait until learning can be performed.

      A012J5DC01
      *a Example
      Table 3. Essential Conditions for Learning
      GTS Display Standard
      Coolant Temp 70 to 100°C
      Intake Air -25 to 120°C
      Fuel Temperature 30 to 96°C
      Fuel Return Temp 35 to 110°C
      Battery Voltage 10 V or higher
      Pilot Quantity State(CAT) READY
      Tip:

      • If the values deviate from the standard above, "Pilot Quantity Learning(Detail)" enters a standby state or is canceled.

      • When the display indicates that "Pilot Quantity State(CAT)" is NG, perform "Pilot Quantity Learning(Detail)" after performing the "Activate the DPF Rejuvenate (PM)" Active Test using the GTS.

        Click hereНажмите здесь

      • When the essential conditions to perform learning are met, the screen will change automatically.

      Note:

      • If "Activate the DPF Rejuvenate (PM)" is performed after an injector compensation code is input but before "Pilot Quantity Learning(Detail)" is performed, DTC P062F is stored and the MIL illuminates due to "Pilot Quantity Learning(Detail)" being incomplete.

      • Using the GTS, make sure that DTCs other than DTC P062F are not output.

      • If DTCs other than DTC P062F are output, perform troubleshooting for those DTCs and then perform "Activate the DPF Rejuvenate (PM)".

      Tip:

      DTC P062F is stored when the value registered in the ECM for an input injector compensation code, catalyst deterioration learning value and/or pilot quantity deterioration learning value is the initial value.

    9. Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or higher for no more than 2 seconds, and then let the engine return to idling.

      A012MVBC01
      *a Example
      A012HR1
      Tip:

      • After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.

      • It is possible to confirm the status of the learning operation during "Pilot Quantity Learning(Detail)" by observing the blinking pattern of the glow indicator light.

      Table 4. Glow Indicator Light Blinking Pattern
      Learning Status Glow Indicator Light Condition
      Conditions essential to start learning have not been met Blinking at 0.5 second intervals
      Conditions essential to start learning have been met Blinking at 1 second intervals
      During racing (learning is being performed) Blinking at 1 second intervals
      Learning is finished Off
      Learning has been canceled Blinking at 1.5 second intervals
      Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern) Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)
      A012I7QE05
      A012HZKE06

    10. When the screen changes, press "Exit".

      A012HD2

    11. Turn the ignition switch off, and then turn the GTS off.

    12. Wait for at least 10 seconds.

    13. Turn the ignition switch to ON, and then turn the GTS on.

    14. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    15. Turn the ignition switch off.

      Note:

      Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the ignition switch off.

      Tip:

      • The main relay turns off after the learned value is stored in the ECM.

      • The main relay turns off within approximately 5 to 10 seconds of turning the ignition switch off.

  7. PILOT QUANTITY LEARNING VALUES CLEAR

    Tip:

    • If the atmospheric pressure is below the threshold value, "Pilot Quantity Learning" will not be completed and DTC P062F is stored. After "Pilot Quantity Learning Values Clear" is performed, DTC P062F will not be stored.

    • Clear the learned values using the following procedure.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON, and then turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot Quantity Learning Values Clear

      Powertrain > Engine and ECT > Utility
      Tester Display
      Pilot Quantity Learning Values Clear

    4. Press "Next".

      A012GDB

    5. Confirm that the atmospheric pressure screen is displayed.

      A012MYAC01
      *a Example

      1. Confirm the displayed atmospheric pressure.

        Standard
        Atmosphere Pressure is below 85 kPa
        Note:

        • If the atmospheric pressure is higher than the standard range for performing "Pilot Quantity Learning Values Clear", do not clear the learned values. Instead, perform "Pilot Quantity Learning".

        • When the atmospheric pressure is higher than the standard range, perform "Pilot Quantity Learning" without initializing the learned values using "Pilot Quantity Learning Values Clear". If the learned values are initialized when the atmospheric pressure is higher than the standard range, the following symptoms may appear. Be sure to correctly follow procedures.

          • Driveability problems

          • Rough idle

          • Emission of white or black smoke, etc.

      2. Proceed to the next screen.

    6. Select the cylinders whose learned value will be cleared.

      A012L1Z
      Note:

      • Multiple cylinders can be selected.

      • Only the cylinders for which injector compensation codes have been written must have their learned value cleared.

    7. After selecting the cylinders whose learned value will be cleared, press "Next" to begin the initialization.

    8. When the screen changes, press "Exit".

      A012IUH

    9. Turn the ignition switch off, and then turn the GTS off.

    10. Wait for at least 10 seconds.

    11. Turn the ignition switch to ON, and then turn the GTS on.

    12. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    13. Turn the ignition switch off and leave the vehicle for 30 seconds or more.

    14. Turn the ignition switch to ON for 1 second.

    15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    16. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes

    17. Confirm that DTCs are not output.

  8. DESCRIPTION OF VIN

    Note:

    The Vehicle Identification Number (VIN) must be input into the replacement ECM.

    Tip:

    The VIN is a 17-digit alphanumeric number. An GTS is required to register the VIN.

    This registration section consists of two parts, Read VIN and Write VIN.

    1. Read VIN: Explains the VIN reading process in a flowchart. This process allows the VIN stored in the ECM to be read, in order to confirm that the two VINs, provided with the vehicle and stored in the vehicle's ECM, are the same.

    2. Write VIN: Explains the VIN writing process in a flowchart. This process allows the VIN to be input into the ECM. If the ECM is changed, or the ECM VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.

  9. READ VIN

    1. Confirm the vehicle VIN.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Engine and ECT / Utility / VIN.

      Powertrain > Engine and ECT > Utility
      Tester Display
      VIN
      A012NE3C01
      *aSelect VIN Read*bNext
      *cDTC P0630 Set*dVIN Previously Stored
      *eVIN Not Stored*fExit
      *g17-digit VIN displayed*hEnd

  10. WRITE VIN

    1. Confirm the vehicle VIN.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Engine and ECT / Utility / VIN.

      Powertrain > Engine and ECT > Utility
      Tester Display
      VIN
      A012LNRC01
      *aSelect VIN Write*bNext
      *cContinue to next illustration*dVIN Previously Stored
      *e17-digit VIN displayed--
      A012LH8C01
      *aInput*bManually input the VIN
      *cOK*dInput Error
      *eNext*fContinue to next illustration
      *gExample--
      A012IXHC01
      *aWriting Successful*bWriting Error
      *cExit*dEnd
      *eTry Again*fTo VIN Write Screen