СИСТЕМА ECD, Diagnostic DTC:P0651

DTC Code DTC Name
P0651 Sensor Reference Voltage "B" Circuit / Open

DESCRIPTION

Refer to DTC P0192.

Click hereНажмите здесь

Refer to DTC P0405.

Click hereНажмите здесь

Refer to DTC P2564.

Click hereНажмите здесь

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0651 Sensor Reference Voltage "B" Circuit / Open

Supplied power (standard: 5 V) from the ECM to the nozzle vane position sensor, fuel pressure sensor and EGR valve position sensor are lower or higher than threshold.

(1 trip detection logic)

  • Nozzle vane position sensor (turbocharger sub-assembly)

  • Open or short in nozzle vane position sensor (turbocharger sub-assembly) circuit

  • Fuel pressure sensor (common rail assembly)

  • Open or short in fuel pressure sensor (common rail assembly) circuit

  • EGR valve position sensor (electric EGR control valve assembly)

  • Open or short in EGR valve position sensor circuit

  • ECM

 Comes on DTC stored
Table 1. DTC Detection Drive Pattern
DTC No. DTC Detection Drive Pattern
P0651 Ignition switch ON

WIRING DIAGRAM

Refer to DTC P0192.

Click hereНажмите здесь

Refer to DTC P0405.

Click hereНажмите здесь

Refer to DTC P2564.

Click hereНажмите здесь

CAUTION / NOTICE / HINT

Note:

When replacing the ECM, perform ECM Initialization and Registration.

Click here Нажмите здесь

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - ECM)

    1. Disconnect the nozzle vane position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B133-3 (VTA1) or B138-38 (VTAI) - Body ground Always 10 kΩ or higher
      B133-1 (VNVC) or B138-37 (VNVC) - Body ground Always 10 kΩ or higher
      B133-2 (VNE2) or B138-36 (VNE2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    GO TO STEP 15

    OK

  2. CHECK TERMINAL VOLTAGE (VC VOLTAGE)

    1. Disconnect the nozzle vane position sensor connector.

      A012K8GC03
      *a

      Front view of wire harness connector

      (to Nozzle Vane Position Sensor)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B133-1 (VNVC) - B133-2 (VNE2) Ignition switch ON 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    GO TO STEP 12

    OK

  3. CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

    1. Disconnect the fuel pressure sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B127-2 (PCR1) or B138-16 (PC) - Body ground Always 10 kΩ or higher
      B127-3 (VC1) or B138-15 (VCS) - Body ground Always 10 kΩ or higher
      B127-1 (E1) or B138-14 (E2S) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    GO TO STEP 15

    OK

  4. CHECK TERMINAL VOLTAGE (VC VOLTAGE)

    1. Disconnect the fuel pressure sensor connector.

      A012FIKC03
      *a

      Front view of wire harness connector

      (to Fuel Pressure Sensor)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B127-3 (VC1) - B127-1 (E1) Ignition switch ON 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    GO TO STEP 12

    OK

  5. CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTROL VALVE ASSEMBLY - ECM)

    1. Disconnect the electric EGR control valve assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B134-5 (VC) or B138-26 (VCEG) - Body ground Always 10 kΩ or higher
      B134-4 (VTA) or B138-27 (EGLS) - Body ground Always 10 kΩ or higher
      B134-3 (E2) or B138-25 (EEGL) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK

  6. CHECK TERMINAL VOLTAGE (VC VOLTAGE)

    1. Disconnect the electric EGR control valve assembly connector.

      A012INOC03
      *a

      Front view of wire harness connector

      (to Electric EGR Control Valve Assembly)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B134-5 (VC) - B134-3 (E2) Ignition switch ON 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG
    NG Нажмите здесь

    OK

  7. REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

    1. Replace the turbocharger sub-assembly.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0651)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off.

    5. Turn the ignition switch to ON.

    6. Turn the ignition switch off and wait for 30 seconds or more.

    7. Turn the ignition switch to ON and wait for 10 seconds or more.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      ResultProceed to
      DTC is not outputA
      DTC P0651 is outputB
    A

    END

    B

  9. REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

    1. Replace the common rail assembly.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  10. BLEED AIR FROM FUEL SYSTEM

    1. Bleed the air from the fuel system.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  11. CHECK WHETHER DTC OUTPUT RECURS (DTC P0651)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    7. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      ResultProceed to
      DTC is not outputA
      DTC P0651 is outputB
    A

    END

    B Нажмите здесь

  12. REPLACE ECM

    1. Replace the ECM.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT Нажмите здесь

    GO TO STEP 14

  13. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE POSITION SENSOR)

    1. Replace the electric EGR control valve assembly.

      Click hereНажмите здесь

      Result
      Proceed to
      NEXT
    NEXT

  14. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off.

    5. Turn the ignition switch to ON.

    6. Turn the ignition switch off and wait for 30 seconds or more.

    7. Turn the ignition switch to ON and wait for 10 seconds or more.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Confirm that the DTC is not output again.

      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT
    NEXT

    END

  15. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT
    NEXT Нажмите здесь

    GO TO STEP 14